DWNSHFT

Guide de préparation

Toyota Supra A80 (Mk4)

Moteur: 2JZ-GTE (RZ, sequential twin turbo) / 2JZ-GE (SZ, NA)

The 2JZ-GTE's iron block and forged crank take far more power than stock, so most builds go straight from bolt-ons to a big single turbo. The sequential twins are best kept for a tidy 350–400 whp street car. The SZ's 2JZ-GE is usually turbocharged (NA-T) or swapped for a GTE.

Ce guide est en anglais pour l’instant.

Toyota Supra A80 (Mk4)

Photo : Mr.choppers · CC BY-SA 3.0 · Wikimedia Commons

  1. Étape 0 · BaseStock (~276 hp crank RZ, ~220 hp SZ)Restore the car to a known healthy state before raising boost.~$2,000–5,000 CAD
  2. Étape 1 · Rue~330–400 whp on steel-wheel twins; keep JDM ceramic twins near 1 barThe classic "BPU" (basic performance upgrade) on the factory twins.~$3,000–6,000 CAD
  3. Étape 2 · Sportive / Piste~500–650 whp on pump fuel, more on E85Single-turbo conversion with a standalone ECU and supporting fuel and cooling.~$12,000–25,000 CAD
  4. Étape 3 · Préparation complète700–1,000+ whp with built internals and E85Reliable 700+ whp, or a dedicated track/drag car.~$25,000–60,000+ CAD

À vérifier avant de modifier

  • JDM twins use ceramic turbine wheels that can shed above about 1 bar; check shaft play and smoke before adding boost.
  • The sequential system relies on many vacuum hoses and VSVs; perished hoses cause boost spikes and dips at the 4,000 rpm transition.
  • Factory boost cut (fuel cut) stops any boost increase until the ECU or a fuel cut defender handles it.
  • 25+ year old cooling system (radiator, hoses, water pump), timing belt (interference engine) and rubber bushings.

Différences entre versions

  • RZ has the Getrag V160 6MT, one of the strongest gearboxes of the era. SZ has the W58 5MT, which is not suited to big power.
  • SZ 2JZ-GE NA-T builds keep the 10:1 pistons; keep boost moderate (~8–10 psi) unless the bottom end is changed.
0

Base

Restore the car to a known healthy state before raising boost.

Puissance (estimation)
Stock (~276 hp crank RZ, ~220 hp SZ)
Budget pièces
~$2,000–5,000 CAD

Moteur

  • Timing belt, water pump, tensioner and cam/crank sealsToyota OEMAisinGates
  • Full vacuum hose refresh (sequential system)Cures most boost transition faults.Toyota OEMsilicone kits

Refroidissement

  • Radiator, hoses and thermostatKoyoMishimotoToyota OEM

Suspension

  • Bushing and ball-joint refreshToyota OEMSuperProWhiteline

Électronique et calibration

  • Coil packs, plugs and boost gaugeNGKDensoDefiAEM

Ordre des travaux

  1. Baseline dyno run plus compression and leak-down test.
  2. Timing belt service and full fluids (engine, V160/W58, diff, coolant, brake).
  3. Replace vacuum hoses and test the sequential transition with a boost gauge.
  4. Check turbo shaft play; plan turbos into Stage 2 if they're tired.
1

Rue

The classic "BPU" (basic performance upgrade) on the factory twins.

Puissance (estimation)
~330–400 whp on steel-wheel twins; keep JDM ceramic twins near 1 bar
Budget pièces
~$3,000–6,000 CAD

Admission et échappement

  • DownpipeHors route / piste seulementThe biggest restriction on the stock setup. Catless versions are off-road/track only.HKSBlitzSR Fab
  • 3-inch cat-back exhaustHKSTomeiBlitzTRD
  • Intake / filterHKSK&NApexi

Électronique et calibration

  • Electronic boost controller + fuel cut defender or piggybackHKS EVCBlitzGreddy

Freins

  • Performance pads and DOT 4 fluidProject MuHawkEndlessMotul RBF600

Roues et pneus

  • 200TW performance tiresYokohamaBridgestoneMichelin

Ordre des travaux

  1. Downpipe and exhaust first, then intake.
  2. Fit the boost controller and fuel cut defender; set about 1.0–1.2 bar on steel twins.
  3. Watch knock and AFR with a wideband; use the best fuel available.
2

Sportive / Piste

Single-turbo conversion with a standalone ECU and supporting fuel and cooling.

Puissance (estimation)
~500–650 whp on pump fuel, more on E85
Budget pièces
~$12,000–25,000 CAD

Suralimentation

  • Single turbo kit (manifold, wastegate, downpipe)A smaller frame is much better for road and track response than a peak-number turbo.Precision 6266/6466Garrett G35BorgWarner EFRHKS

Refroidissement

  • Front-mount intercoolerHKSGreddyMishimoto
  • Oil cooler and larger radiatorHKSTrust/GreddyKoyo

Alimentation

  • 1000–1300 cc injectors + 450 lph pump + regulatorInjector DynamicsDeatschWerksWalbro/TIAeromotive

Électronique et calibration

  • Standalone ECUHaltechLinkAEM InfinityMotec

Transmission

  • Twin-plate or uprated clutchOS GikenExedyOgura

Suspension

  • CoiloversTeinKWOhlinsBC Racing

Freins

  • Big brake kit or high-temp padsBremboAP RacingEndless

Ordre des travaux

  1. Add the fuel system and ECU before the turbo goes on.
  2. Fit the turbo kit, FMIC and oil/coolant lines, then do a conservative base map.
  3. Dyno tune; add flex-fuel if E85 is available locally.
  4. Upgrade the clutch at the same time as the turbo, not after it slips.
3

Préparation complète

Reliable 700+ whp, or a dedicated track/drag car.

Puissance (estimation)
700–1,000+ whp with built internals and E85
Budget pièces
~$25,000–60,000+ CAD

Moteur

  • Forged rods and pistonsManleyCarrilloCPJE
  • ARP head studs, MLS head gasket, upgraded oil pumpARPHKSCometicToyota/TRD
  • Cams and valve springsHKSBrian CrowerKelford

Suralimentation

  • Larger single turboPrecision 6870/7275Garrett G42BorgWarner S300/S400

Transmission

  • Built or replacement gearbox, driveshaft, axlesDriftmotionThe Driveshaft ShopQuaife

Intérieur

  • Roll cage, seats, harnessesCuscoBrideSparcoSchroth

Ordre des travaux

  1. Build the short block and head together; balance the rotating assembly.
  2. Check the V160 or plan a sequential or dog box for drag use.
  3. Upgrade the driveline (axles, driveshaft, diff) to match the torque.
  4. Add the cage, seats and fire system before chasing lap or ET records.

Les chiffres de puissance et de budget sont des estimations (pièces seulement, en $ CA), pas des garanties : le carburant, la calibration, le climat et le choix des pièces changent tout. Les marques sont des exemples, pas des commandites. Retirer ou vider les catalyseurs, ou désactiver les systèmes antipollution, est illégal sur les voitures de route au Canada et aux États-Unis; les pièces marquées « hors route / piste seulement » sont réservées aux véhicules de compétition.

Sources